[4LTURBO] Shitter Work Ute

[Turbo2.6L]

She’s almost ready, so thought it time to start a showcase on the old girl. Here goes…

2003 BA XR6 Turbo Ute

Engine
Brand New Prepped FG Block
FG Crank
Mahle Powerpack Pistons
Mahle Competition Ring Set
Atomic 660Kw Rods
ARP Main Caps & Head Studs
Billet Oil Pump Gears
BF F6 Cams
Standard BA Head
Standard Fraud Head Gasket
Balanced & Assembled by Rob @ Monsta Torque

Driveline
Performance Auto's 'Super Comp' C4 Transmission
Transmission Specialties Transbrake
Uprated Billet Input Shaft
TCE 3000rpm Converter
Dellows Bellhousing
B&M Tranny Cooler with Teflon Braided lines
Final Drive Tailshaft with Billet Uni's
Standard LSD
Standard Axles
3.45:1 Gearset
Tailshaft Loop
9” Conversion From Final Drive is on the cards in the near future

Bolt-Ons
Garret 4094 Turbs with 0.86 Rear Housing
6boost Low Mount Manifold
Tial 60mm Gate with Screamer Pipe
Process West Plenum
Process West Cooler
Process West Hotside & Coldside Piping
Battery Relocated to rear
Process West 4” Intake Pipe & Airbox
Siemens 60lb Injectors
Bosch 044 Pump x 2
RCI 60L Ally Fuel Cell Located in Tray
Teflon Braided Fuel Lines
Prestige Exhaust Custom Dump Pipe
SMB 5” ‘Special’ High Flow Cat
SMB 4” Cat-Back System
Monsta Torque Catch Can Setup
CAPA Flash Box with Monsta Torque Tune

Wheels/Tyres/Brakes/Suspension
19 x 8” & 19 x 10” Simmons FR19’s (More dish than Tocchi’s shitters :p)
245/35 Sumitomo HTRZ & 275/30 TOYO Proxes T1R Rubber
Brembo 6pot Front Calipers with 355mm Rotors
Braided Lines
Pedders Coilover Shocks Up Front
Reset Rear Leafs
27mm Adjustable Front Swaybar, No Rear Swaybar

Interior
Retrimmed in Red & Black Leather
FPV Fat Steering Wheel
FPV Dual Zone Climate Control Installation
FPV Dash Cluster
FPV Guage Holder with Autometer Cobalt Boost & Oil Pressure Guages
B&M Pro Ratchet Shifter with Transbrake Button
Greddy Profec B EBC
Beltronics RX75 Pro Remote Mount Detector

Exterior
Genuine Hardlid with Shithouse Aftermarket Spoiler
Dented Rear Panel from Previous Owner

Performance
Power – Little over 500rwhp on run-in tune
¼ Mile Time – Aiming for 13 seconds :lol:
¼ Mile MPH – ~106mph

http://i129.photobucket.com/albums/p233/03XR6T/IMG_2768.jpg

http://i129.photobucket.com/albums/p233/03XR6T/IMG_2772.jpg

http://i129.photobucket.com/albums/p233/03XR6T/IMG_2772.jpg

http://i129.photobucket.com/albums/p233/03XR6T/IMG_2766.jpg

http://i129.photobucket.com/albums/p233/03XR6T/IMG_2767.jpg

http://i129.photobucket.com/albums/p233/03XR6T/IMG_2754.jpg

http://i129.photobucket.com/albums/p233/03XR6T/IMG_2756.jpg

http://i129.photobucket.com/albums/p233/03XR6T/IMG_2769.jpg

http://i129.photobucket.com/albums/p233/03XR6T/IMG_2770.jpg

http://i129.photobucket.com/albums/p233/03XR6T/IMG_2750.jpg

http://i129.photobucket.com/albums/p233/03XR6T/IMG_2760.jpg

[mitchy]

Dented Rear Panel from Previous Owner
where can i buy one of those from? :lol:

not to start a shitfight of 'claimed' HP figures, but do you have a rough idea of what it will put out?

[Azrian]

100 killer wasps.

Sound awesome mate.

[xr06t]

you gonna stick with the 4" zorst?

[XF Falcon]

Sounds like it might be able to spin a tyre on some wet grass ;)

Look forward to seeing it done Deano.

[Tocchi]

mitchy, most likely situation..

compared to other workshops/tuners
dean's power will be lower
but his times will be faster.

i think he's aiming for a 540kw 12 second pass :)


cant wait to see this run dean :)
gonna get some sponsorship from bunnings?

[Gladio]

Awsome, What colour is it?

[Turbo2.6L]

Dented Rear Panel from Previous Owner
where can i buy one of those from? :lol:

not to start a shitfight of 'claimed' HP figures, but do you have a rough idea of what it will put out?

I can dent any panel you choose on the 31 for a mere $100 :D
Powerwise, chasing whatever it takes to run 140mph+


you gonna stick with the 4" zorst?

See how we go. May opt for another system like the F6 had...


mitchy, most likely situation..

compared to other workshops/tuners
dean's power will be lower
but his times will be faster.

i think he's aiming for a 540kw 12 second pass :)


cant wait to see this run dean :)
gonna get some sponsorship from bunnings?

ROFL!
Na bunnings wont want anything to do with it soon, Nizpro gear is coming off to make way for something better.


Awsome, What colour is it?

Black.

[RMX]

Solid build, Should be a lot of fun!

Keen to see dyno and 1/4 results.

[Daisy]

low mount is for homo's

[Turbo2.6L]

High Mount is for show pony's.
You been hanging around Adrian too long :lol:

[Azrian]

Munch ass.

[xr6tego]

Sounds awesome Dean. Looking forward to seeing it out and about.

[Turbo2.6L]

Cheers Brendan :D

[Tre-Cool]

i thought this was going to be a drag only car?

[ED40]

Low mount for the win.

What you aiming for? 9's? That parts list is very impressive.

[Turbo2.6L]

Na, street duties predominently but i want it to run a decent time/mph as well. There'll obviously be a bit of a compromise but i'd rather have a quick street car that runs good numbers than a dedicated drag car that runs slightly quicker.
Will be caged/chuted if necessary & the 9" rear end wont be far off to prevent axle breakages every time i get on the transbrake!

ED40, no predictions on times via forums as i'd hate to say i'm aiming for 12's & only run a 13... Should do alright though.

[Tocchi]

Front mount turbo ftw :p

[shane]

Looks like a tough build. Are you going to run it in competition or just punch out a number and be happy with that. It would be great to see a late model falcon in super sedan. :)

[xr6tego]

Yeah with that setup, a 12 maybe a little optimistic. Perhaps if you say a low 14 and if you manage to pop into the 13's you'll be pretty happy.......

[AGIT8D]

9 inch rear end sounds good.. how well do they hook up with the leaf rear?

[Jizz-Lebrity]

Sounds very tough. I guess you didn't notice the dents/scratches I put on your Simmons then, lucky :p


mitchy, most likely situation..

compared to other workshops/tuners
dean's power will be lower
but his times will be faster.

i think he's aiming for a 540kw 12 second pass :)


cant wait to see this run dean :)
gonna get some sponsorship from bunnings?

98% pure fail.

[thrtytwo]

good build mate, should be quick im sure



i think he's aiming for a 540kw 12 second pass :)




ED40, no predictions on times via forums as i'd hate to say i'm aiming for 12's & only run a 13... Should do alright though.


Yeah with that setup, a 12 maybe a little optimistic. Perhaps if you say a low 14 and if you manage to pop into the 13's you'll be pretty happy.......


took me a good five minutes to figure out you weren't all on the crack pipe, thinkin, dont xr6T run high 12s with a zorst and a tune. Ahh the beauty of sarcasm

[Jizz-Lebrity]

Autos do, manuals generally run about as fast as you can tow them off the track after they have broken something.

[F6Hoon]

what are our chances of seeing a scene like this in the near furture perhaps on a cruise???


http://www.youtube.com/watch?v=WuIgL3WE1iY&feature=related

tough ute from what rob has told me its gonna be angry as :boink:

[Yakky Bear]

sounds tough dean cant wait to see it :)

[RBS13]

so the simmons were 10" on the rear??? get some pics up!!!!

[Turbo2.6L]

Looks like a tough build. Are you going to run it in competition or just punch out a number and be happy with that. It would be great to see a late model falcon in super sedan. :)

See how we go i suppose.
If it runs consistently (as consistent as a street car can get) i'll have a crack at next season :D


9 inch rear end sounds good.. how well do they hook up with the leaf rear?

Average.
Looking into 9" with coilies,but may be more trouble than it's worth...


what are our chances of seeing a scene like this in the near furture perhaps on a cruise???


http://www.youtube.com/watch?v=WuIgL3WE1iY&feature=related

tough ute from what rob has told me its gonna be angry as :boink:

Will be out & about very soon!


so the simmons were 10" on the rear??? get some pics up!!!!

Surely were :)
Measured them with no tyres on & they were a shade over 10" at the rear & 8" front!

[mitchy]

Surely were :)
Measured them with no tyres on & they were a shade over 10" at the rear & 8" front!

where did you measure them?
width measurements are taken inside the bead, not the overall rim width in case you didnt know

[Daisy]

^^bingo, my 11inch simmons measure 12.5 from outer to outer. (half the reason they dont fit, the other half is the fact i`m a dummy)

look forward to seeing some transbrake loving.

[xr06t]

put cheap tyres on the back for the 1st transbrake skid, because i dont wanna see a girly attempt!

[Tocchi]

yeh mine measure 10.5" on the rear... oh how i wish they were.. but in fact they are 9.5" rims


agree to transbrake !

[Turbo2.6L]

Measure slightly under 11" from lip to lip, hence why we figured they were 10" wide using the correct way to measure.
Already have tyres lined up for transbrake destruction :lol:

[F6Hoon]

Measure slightly under 11" from lip to lip, hence why we figured they were 10" wide using the correct way to measure.
Already have tyres lined up for transbrake destruction :lol:


Please video for the entertainment of us that can't make the first episode of transbrake love!

[miksta]

I demand another massive fucking skid at Retravision, with pizzafaces car parked behind you with his windows down and Brockas in his double pluggers getting burnt by red hot flying rubber lols. :werd:

[Turbo2.6L]

I'm keen!

[Torquen]

Autos do, manuals generally run about as fast as you can tow them off the track after they have broken something.

QFT. lol.

Sounds good Dean! Super keen to see this in action :)
Best of luck with the rest of the build!

[KeithTheBricklayer]

looks gay

i wnt your simmons tho bitch

[SSICK]

blamey place, culdesac transbrakes skids!

[Turbo2.6L]

Haha i'm sure Mitch & Deb will love that :lol:
Ute is finished & in my garage... Just too slack to wash it & get decent pics. Will do soon.

[KeithTheBricklayer]

go go go go

pics of inside cabin+under bonnet+your missus+ the outside

gogogogogo

[Huy]

No pics ftl, dean.

[DenZel]

SHOWcase thread...keen for pics.

[ovaxitd]

pics biatch... is it tuned yet ?? sounds like a weapon...

[Tocchi]

go go go go

pics of inside cabin+under bonnet+your mum+ the outside

gogogogogo

fixed

[Turbo2.6L]

Yes it's tuned, sort of... Run-in tune has seen slightly over 500rwhp through a converter that is extremely loose & needs to be re-opened. Will trundle around as is for a bit & then take it back to be leaned on.
Pics of mum for Tocchi to come soon as well!

[j3rk]

Run-in tune has seen slightly over 500rwhp So much win in that statement... keen to see results of real tune!

[YOUR MATE]

Lol Tocchi your mum is a fucking fox, I say you post pics first.

[esky]

then post pics of your sister second

[Yakky Bear]

then post pics of your sister second

+1

Cankles thread and this thread


SAME SAME....needs moar pics dean

[Turbo2.6L]

Pics finally added bitches! Although, someone really needs to teach me how to use my DSLR... Seen better pics come off peoples camera phones! :lol:
Before anyone asks, yes it's filthy, yes that is EFI hose i used for the breather & turbo water line, yes i have an exhaust leak between manifold & turbs (hence the exhaust soot on rocker cover & top of turbo), yes the interior would of looked more at home in a VK back in the 80's.

Enjoy :D

[Tre-Cool]

what pics?

[Turbo2.6L]

Sorry, first post updated!

[31-EVO]

Looks excellent, bye bye hard top spoiler ?

[Turbo2.6L]

Had a flat hardlid lined up to swap with mine but it fell through. Leaving it for now until i find another one as i wont pay what Ford charge for a new one, and wont plug holes with rubber grommets/electrical tape like most commodores driving around atm.

[F6Hoon]

looks awesome with ur rims man, last time i was at robs it had stock rims, simmons looked bombed against the black

[Gladio]

How come you are selling it already?

[Turbo2.6L]

Not actively selling, just putting it out there that it's available for the right price. Definitely wont be going before September as i want to run it down the strip.

[Torquen]

Niceeeeeeeeee :) Keen to see do a skid!

[Turbo2.6L]

Doesn't do them. Driver's too soft!

[Torquen]

Viagra + right pedal to the floor = problem solved!

[Tre-Cool]

SO u gonna be at 1st waw (if it doesnt get rained out)?

Keen to come watch lines down the track, possibly in seat too if she slides around a bit!

lol

[xr6tego]

Looks good Dean, although needs a bath...
Don't you think your aiming a little low for your quarter mile time. I would of thought a low 14 maybe more realistic, or you going to run some special juice for it?

[Turbo2.6L]

Viagra + right pedal to the floor = problem solved!

Not keen. I'm a law abiding citizen :D


SO u gonna be at 1st waw (if it doesnt get rained out)?

Keen to come watch lines down the track, possibly in seat too if she slides around a bit!

lol

Yep i'll be there. Shouldn't be too bad on slicks, but we shall see!


Looks good Dean, although needs a bath...
Don't you think your aiming a little low for your quarter mile time. I would of thought a low 14 maybe more realistic, or you going to run some special juice for it?

Jungle juice for the 13sec pass Brendan :)
Seriously though, if it runs a high 10 like the F6 did i'll be stoked!

[xr6tego]

Mate you should shit that in i would of thought. How are you going to go with the fun police down there? Wont they kick you out if you bust into the 10's without a cage?

[Turbo2.6L]

Surely will.
If i decide to keep it a while, it will get caged & i'll get serious with the rear end. For now i just enjoy driving it on the street & looking in the mirror to see these funny black lines following me through top gear :lol:

[Phyber]

Wouldn't be the first time getting booted from there eh! Would be keen to watch if I could get down there in time for WAW, when I ran last season I got in at like 7 :/



Top gear is only third :p

[Huy]

Damn it's dirty! :D

Nice one, Dean. Looking forward to seeing said painted lines.

[Turbo2.6L]

Wouldn't be the first time getting booted from there eh! Would be keen to watch if I could get down there in time for WAW, when I ran last season I got in at like 7 :/



Top gear is only third :p

3rd is still 1:1 :)


Damn it's dirty! :D

Nice one, Dean. Looking forward to seeing said painted lines.

Looking forward to showing you! Ha

[RMX]

Dare I ask what your chasing for it?

[esky]

15k

it is a ba after all

[RMX]

... and its missing a gear.

[ovaxitd]

Swap for x100 and cash my way...







:p

[Turbo2.6L]

Dare I ask what your chasing for it?

Not chasing anything in particular. If someone makes me a decent offer, it's theirs if i'm happy.


15k

it is a ba after all

I'll sell for $15k & buy your shitheap for $20k then? It's only an evo 7 :p


Swap for x100 and cash my way...







:p

Yea na!

[1manwolfpack]

Beast of a car mate

[sprint347]

I want those wheels!

[Tocchi]

No you don't...


As they say, the only ppl that say dish is over rated are the ppl with no dish

Lol

[mitchy]

nert, dish is gay!

[Turbo2.6L]

http://www.antilag.com/forums/showthread.php?t=42662

Help a nigga out!